Skip to main content

What Happens When the Power Plant Blackout?

 Electricity is one of the basic needs of human beings in today’s life.

Everything from our life is utilized by electrical energy that may be from health to fun and from transportation to traffic.


As a result, social and economic influences are inevitable in an interrupted situation. 

In normal operating conditions energy production systems enable electricity to reach consumers easily.


Energy interruptions can occur due to disturbing currents.  When the power system is defined as a power grid collapse, which is partially or completely out of order, it is the most negative situation for power system operators.


Blackout of Electrical Power Grid

  • The electric power grid serves as a bridge between energy production plants and consumers.
  • Energy supply and demand balance problems may occur at any time.
  • These problems cause the voltage and frequency of the power grid to increase or decrease.
  • Through these distortions, the power system is causing the power generation plants to be out of order through the protection relays.
  • The synchronization in the power grid is starting to finish and the system is partially or completely collapsed.
  • In other words, the blackout of the system is inevitable if the frequency and voltage values of the system are not expected.


What is a Blackout in a Power Plant?

Blackout is the condition when a power plant can’t produce any power.

It is a total crash of the power grid due to an imbalance between power generation and power consumption. In the power plant, the power is generated and sent to the switchyard, and finally to the transmission system known as the grid.


All turbine generators and transmission lines of the power plant are interconnected with each other through bus bars.


The plant can send generated power to the grid, and also receives the same power from the grid when required.

Why do Blackouts Occur in Power Plants?

 A blackout occurs when there is a greater demand of load than the generated power the turbine generators will trip.


Blackout in the thermal or any power plant occurs mainly due to the problem raised in the grid station that connects the power plant and the nearest substation.


This occurs when all the transmission lines connected to the switchyard trip which leads to tripping of all turbine generators and opening of the grid breaker.

Blackout in powerhouse may be caused by


  • Excessive power demand exceeds the generating capacity of the power source.
  • Weather conditions like hurricanes toppling power lines.
  • Breakdown of grid substations.
  • Short circuit faults on power lines.
  • Vehicle accidents crashing to electric poles or grid steel towers.
  • Forest fires or building fires close to power lines.

What Happens When the Power Plant Blackout?

When the plant gets a blackout, the plant can’t produce any power, and may not get any emergency power supply from the grid station for its internal use as all the parts of plant equipment are isolated from the grid and load centers. 


Under such emergencies, the plant must establish some auxiliary power to run the plant equipment. And if the turbine trips during home load, the blackout of the plant would occur as emergency power from the substation could not be got, resulting in the stopping of all equipment of the plant.


The diesel generator acts as a source of power back up to the plant in such emergency conditions.


The diesel generator is an auxiliary source that must be provided to produce the necessary power supply to carry out essential steps to avoid any detrimental effects on various plant equipment.


When any problems occur in the plant or the nearest substation, the grid breaker of the plant gets opened or released to avoid damage to the plant equipment.

General Reasons for Power Grid Collapses
The grid collapses that occur in power systems are due  to  five main factors

  1. Voltage loss.
  2. Frequency loss.
  3. Phase angle imbalance.
  4. Production – consumption imbalance  and
  5. Synchronization loss.

What is the Procedure to follow after a Blackout in a Power Generating Station?

If the power station has blacked out, we must notify


  • The main steam stop valve must be closed.
  • The emergency oil pump must turn on for lubrication.
  • Turbine drains must be opened.
  • The system controller must be shut down.
  • Now we must open all connecting switches and circuit breakers.
  • Blow down the steam or fuel supply that operates the steam turbines to preclude bent shafts.
  • Receive a report from station maintenance.
  • Initiate all emergency procedures.
  • Determine the cause of the blackout.
  • Initialize any required minor repairs needed.
  • Restart the system with the right procedure.
  • Make  re-synchronization


Labels:

Comments

Post a Comment

Popular posts from this blog

PLC Program for Mixing Tank

 Create a ladder diagram for controlling a batch mixing process. Implement a PLC program for mixing tank or Mixing Process using PLC Ladder Logic. PLC Program for Mixing Tank Fig : Mixing tank A tank is used to mix two liquids. The required control circuit operates as follows: A. When the START button is pressed, solenoids A and B energize. This permits the two liquids to begin filling the tank. B. When the tank is filled, the float switch trips. This de-energizes solenoids A and B and starts the motor used to mix the liquids together. C. The motor is permitted to run for 1 minute. After 1 minute has elapsed, the motor turns off and solenoid C energizes to drain the tank. D. When the tank is empty, the float switch de- energizes solenoid C. E. A STOP button can be used to stop the process at any point. F. If the motor becomes overloaded, the action of the entire circuit will stop. G. Once the circuit has been energized, it will continue to operate until it is manually stopped. Solution...
1 comment
Read more

What is Relay? How it Works? Types, Applications, Testing

 We use relays for a wide range of applications such as home automation, cars and bikes (automobiles), industrial applications, DIY Projects, test and measurement equipment, and many more. But what is Relay? How a Relay Works? What are the Applications of Relays? Let us explore more about relays in this guide. What is a Relay? A Relay is a simple electromechanical switch. While we use normal switches to close or open a circuit manually, a Relay is also a switch that connects or disconnects two circuits. But instead of a manual operation, a relay uses an electrical signal to control an electromagnet, which in turn connects or disconnects another circuit. Relays can be of different types like electromechanical, solid state. Electromechanical relays are frequently used. Let us see the internal parts of this relay before knowing about it working. Although many different types of relay were present, their working is same. Every electromechanical relay consists of an consists of an Elect...
1 comment
Read more

Chlorine dioxide Analyzer Principle

 Chlorine dioxide measurement Chlorine dioxide (ClO2) is an instable, non-storable, toxic gas with a characteristic scent. The molecule consists of one chlorine atom and two oxygen atoms – represented in the chemical formula ClO2. It is very reactive. To avoid the risk of spontaneous explosions of gaseous chlorine dioxide or concentrated solutions, it is generally handled in dilution with low concentrations. ClO2 is soluble in water, but tends to evaporate quickly. Typically it is prepared on site, for example from hydrochloric acid and sodium chlorite. The procedure provides solutions with approx. 2 g/l ClO2 that can be safely handled and stored for several days. Image Credits : krohne Sensor Parts : Reference electrode Applied chlorine dioxide specific potential Current needed to maintain the constant potential Counter electrode Measuring electrode The disinfection effect of ClO2 is due to the transfer of oxygen instead of chlorine, so that no chlorinated byproducts are formed. C...
6 comments
Read more