One Shot Rising PLC Example Program

Build the ladder logic program to turn ON or OFF the lamp using single push buttons using one shot rising (ONR) instruction.

ONE Shot Rising (OSR) Instruction

One shot Rising is used to develop a signal/Pulse that is exactly one scan in duration. When a signal is applied to a contact/Push Button, no matter how long the signal stays on, a single pulse of one scan length is generated after the one shot.

List of Inputs and Outputs

PLC Logic Conditions

One Shot Rising PLC Program

Program Description

RUNG 0000

Start/Stop Push Button is connected with one shot rising bit with the output memory bit.

RUNG 0001

Previous rung output bit and Lamp output bit are connected in X-OR gate logic to make the condition possible. Interlocking of output bit is used to turn the output ON/OFF in different condition.

Conclusion:

The above explained ladder logic for lamp turn ON/OFF using single push button is for example only. We can use this example program to understand the working of Push Buttons, one shot rising in AB PLC.

-END747-

Comments

PLC Program for Mixing Tank

Create a ladder diagram for controlling a batch mixing process. Implement a PLC program for mixing tank or Mixing Process using PLC Ladder Logic. PLC Program for Mixing Tank Fig : Mixing tank A tank is used to mix two liquids. The required control circuit operates as follows: A. When the START button is pressed, solenoids A and B energize. This permits the two liquids to begin ﬁlling the tank. B. When the tank is ﬁlled, the ﬂoat switch trips. This de-energizes solenoids A and B and starts the motor used to mix the liquids together. C. The motor is permitted to run for 1 minute. After 1 minute has elapsed, the motor turns off and solenoid C energizes to drain the tank. D. When the tank is empty, the ﬂoat switch de- energizes solenoid C. E. A STOP button can be used to stop the process at any point. F. If the motor becomes overloaded, the action of the entire circuit will stop. G. Once the circuit has been energized, it will continue to operate until it is manually stopped. Solution...

What is Relay? How it Works? Types, Applications, Testing

We use relays for a wide range of applications such as home automation, cars and bikes (automobiles), industrial applications, DIY Projects, test and measurement equipment, and many more. But what is Relay? How a Relay Works? What are the Applications of Relays? Let us explore more about relays in this guide. What is a Relay? A Relay is a simple electromechanical switch. While we use normal switches to close or open a circuit manually, a Relay is also a switch that connects or disconnects two circuits. But instead of a manual operation, a relay uses an electrical signal to control an electromagnet, which in turn connects or disconnects another circuit. Relays can be of different types like electromechanical, solid state. Electromechanical relays are frequently used. Let us see the internal parts of this relay before knowing about it working. Although many different types of relay were present, their working is same. Every electromechanical relay consists of an consists of an Elect...

Chlorine dioxide Analyzer Principle

Chlorine dioxide measurement Chlorine dioxide (ClO2) is an instable, non-storable, toxic gas with a characteristic scent. The molecule consists of one chlorine atom and two oxygen atoms – represented in the chemical formula ClO2. It is very reactive. To avoid the risk of spontaneous explosions of gaseous chlorine dioxide or concentrated solutions, it is generally handled in dilution with low concentrations. ClO2 is soluble in water, but tends to evaporate quickly. Typically it is prepared on site, for example from hydrochloric acid and sodium chlorite. The procedure provides solutions with approx. 2 g/l ClO2 that can be safely handled and stored for several days. Image Credits : krohne Sensor Parts : Reference electrode Applied chlorine dioxide specific potential Current needed to maintain the constant potential Counter electrode Measuring electrode The disinfection effect of ClO2 is due to the transfer of oxygen instead of chlorine, so that no chlorinated byproducts are formed. C...

TILI Automation

Search This Blog