What is Interface Module in Siemens PLC?

In this article, we will learn about the interface module (IM) used in the Siemens PLC.

The data transfer between I/O modules or between higher levels of PLCs takes place via an interface module.

I know that many people have heard this word remote I/O, this is achieved by installing an interface module.

Remote I/O is used to reduce long wire run, reduce complexity while troubleshooting, and provide a cost-effective solution.

Let’s assume that in the plant we have to install a bunch of field devices that are far away from the control room.

In such a case instead of pulling wires from field to control room can increase the cost significantly and also make troubleshooting of a system more difficult.

To make things simple, first, move all the I/O modules to the field area and add interface module with it.

Now, connect supported communication port from the control room’s CPU to interface module to establish communication with each other.

This way you only require one cable for communication between devices, which reduces the cost of wiring and complexity.

Interface Module in Siemens PLC

As you can see in the below image that how an interface module is used to transfer data over a long distance.

In the case of a critical system, you can pull one more communication cable as a redundant system to prevent an unexpected shutdown.

There is one more way to use the interface module in the control panel.

In s7-300 series of CPU support three rack and eleven module configurations.

This way you can add the third rack and do follow the same step to establish a connection.

On the software side, you can find many different types of interface modules. You can choose as per your application and hardware.

You can connect an interface module through PROFINET or by PROFIBUS method to communicate.

Comments

PLC Program for Mixing Tank

Create a ladder diagram for controlling a batch mixing process. Implement a PLC program for mixing tank or Mixing Process using PLC Ladder Logic. PLC Program for Mixing Tank Fig : Mixing tank A tank is used to mix two liquids. The required control circuit operates as follows: A. When the START button is pressed, solenoids A and B energize. This permits the two liquids to begin ﬁlling the tank. B. When the tank is ﬁlled, the ﬂoat switch trips. This de-energizes solenoids A and B and starts the motor used to mix the liquids together. C. The motor is permitted to run for 1 minute. After 1 minute has elapsed, the motor turns off and solenoid C energizes to drain the tank. D. When the tank is empty, the ﬂoat switch de- energizes solenoid C. E. A STOP button can be used to stop the process at any point. F. If the motor becomes overloaded, the action of the entire circuit will stop. G. Once the circuit has been energized, it will continue to operate until it is manually stopped. Solution...

What is Relay? How it Works? Types, Applications, Testing

We use relays for a wide range of applications such as home automation, cars and bikes (automobiles), industrial applications, DIY Projects, test and measurement equipment, and many more. But what is Relay? How a Relay Works? What are the Applications of Relays? Let us explore more about relays in this guide. What is a Relay? A Relay is a simple electromechanical switch. While we use normal switches to close or open a circuit manually, a Relay is also a switch that connects or disconnects two circuits. But instead of a manual operation, a relay uses an electrical signal to control an electromagnet, which in turn connects or disconnects another circuit. Relays can be of different types like electromechanical, solid state. Electromechanical relays are frequently used. Let us see the internal parts of this relay before knowing about it working. Although many different types of relay were present, their working is same. Every electromechanical relay consists of an consists of an Elect...

Ferrules and Cross Ferruling

Ferrules are identification labels provided for every wire terminations in an instrument, equipment, or electrical/instrumentation control panels. These tube-shaped sleeves can be inserted easily on each individual wire in a multi-core cable. In earlier days fixed digits/letters are used as ferrules, but now Instrumentation engineers/technicians prints out desired ferrules by using a ferrule printing machine. Typical Ferrule The numbers/ letters on the ferrules will be given as per the approved electrical hook up or loop diagrams. This helps technicians to easily identify a particular loop/wiring from a series of terminal blocks and to troubleshoot the desired terminal connection. Separate numbers on the ferrules distinguish the positive and negative polarities of wires, thus ensure the polarity protection of the instrument. Cross Ferruling As a wire is connected on its both ends, it is quite useful to use a cross reference method for wire identification. Unlike normal ferru...

TILI Automation

Search This Blog