Skip to main content

Pressure Switch Calibration Procedure

 Pressure switches are commonly used in the process industry for a wide range of applications. A pressure switch is a form of sensor that closes or opens an electrical contact when a certain pressure has been obtained either through a pressure rise or a pressure drop.

Pressure switches are used to monitor, control, or provide a caution or warning for a pressure related process. The repeatability, accuracy, and functionality of a pressure switch often tie directly into the safety or efficiency of a process and thus it becomes important that pressure switches are verified and calibrated to ensure their proper function in the process.

Pressure Switch Calibration

There are several terms that describe the function of a switch which need to be understood when testing a pressure switch:

Set point:

The pressure which the switch will change state.

 Normal State:

The state of the switch when at barometric pressure or ideal state.

Depends on Pressure switch type.(typically it would be either OPEN or CLOSED).

Reset:

The pressure at which the switch resets back to the normal state.

Tolerance:

The allowable variation from the set point pressure.

Repeatability:

The closeness of agreement between the results of consecutive measurements.

Dead Band:

The pressure difference between the change-of-states.

(i.e. OPEN to CLOSE or CLOSE to OPEN).

Trip Type:

This is the direction to which the change-of state should happen.

If the trip type is low, this means the change-of-state happens when the pressure is falling.

If the trip type is high, this means the change-of-state happens when the pressure is rising.

Calibration or Verifying a Pressure Switch


Before implementing the steps, you need to confirm the setpoint and the dead-band of the Pressure switch. In addition, The pressure switch must be depressurized and isolated.

Consider our Pressure Switch is a normally open switch, so we will need to test when the switch changes between open to close. Next, we’ll test the reset pressure (from closed to open) and lastly, repeat the test at least once to determine repeatability.

Required Tools:
  1. we must use a pressure calibrator or Multimeter (DMM) to determine the current state of the switch.
  2. we need to have a pressure generation device (preferably a hand pump ).
  3. we will need a way to measure the true pressure using a pressure calibrator or Pressure gauge.
Calibration Procedure :
  1. First we connect the pressure gauge and Pressure switch to the hand pump as shown in above figure.
  2. Then we need to measure the present status (NO/NC) of electrical output of the switch with the multimeter.Put multimeter in Continuity mode.
  3. Note: Here in this example our pressure switch considered is Normally open type. So when you connect the multimeter before calibration we have default Normally Open (NO) signal as output.
  4. With our connections complete, we are ready to perform the calibration. We do this by increasing pressure until we detect a change in the switch.
  5. Now increase the pressure with the help of hand pump.
  6. When we see the switch change state from open to close, we record the result.
  7. Next, we decrease the pressure till we see the switch reset (change from close to open) and record the results.
  8. Also record the dead band.
  9. Lastly, we would repeat this test at least once to determine repeatability. The difference between set point and rest pressures is the dead
  10. band.The dead band must be within the range. The deadband & setpoint of pressure switch available on nameplate of pressure switch.
  11. For Normally closed Pressure switch calibration also follows the same above mentioned procedure. But the default status of Normally closed type Pressure switch will have N.C. signal as output. When testing with increasing pressure the output state changes from N.C. to N.O and while on decreasing pressure the output state changes from N.O. to N.C. Remaining all steps are same. Thats it. very simple.


Labels:

Comments

Post a Comment

Popular posts from this blog

PLC Program for Mixing Tank

 Create a ladder diagram for controlling a batch mixing process. Implement a PLC program for mixing tank or Mixing Process using PLC Ladder Logic. PLC Program for Mixing Tank Fig : Mixing tank A tank is used to mix two liquids. The required control circuit operates as follows: A. When the START button is pressed, solenoids A and B energize. This permits the two liquids to begin filling the tank. B. When the tank is filled, the float switch trips. This de-energizes solenoids A and B and starts the motor used to mix the liquids together. C. The motor is permitted to run for 1 minute. After 1 minute has elapsed, the motor turns off and solenoid C energizes to drain the tank. D. When the tank is empty, the float switch de- energizes solenoid C. E. A STOP button can be used to stop the process at any point. F. If the motor becomes overloaded, the action of the entire circuit will stop. G. Once the circuit has been energized, it will continue to operate until it is manually stopped. Solution...
1 comment
Read more

What is Relay? How it Works? Types, Applications, Testing

 We use relays for a wide range of applications such as home automation, cars and bikes (automobiles), industrial applications, DIY Projects, test and measurement equipment, and many more. But what is Relay? How a Relay Works? What are the Applications of Relays? Let us explore more about relays in this guide. What is a Relay? A Relay is a simple electromechanical switch. While we use normal switches to close or open a circuit manually, a Relay is also a switch that connects or disconnects two circuits. But instead of a manual operation, a relay uses an electrical signal to control an electromagnet, which in turn connects or disconnects another circuit. Relays can be of different types like electromechanical, solid state. Electromechanical relays are frequently used. Let us see the internal parts of this relay before knowing about it working. Although many different types of relay were present, their working is same. Every electromechanical relay consists of an consists of an Elect...
1 comment
Read more

Ferrules and Cross Ferruling

 Ferrules are identification labels provided for every wire terminations in an instrument, equipment, or electrical/instrumentation control panels. These tube-shaped sleeves can be inserted easily on each individual wire in a multi-core cable. In earlier days fixed digits/letters are used as ferrules, but now Instrumentation engineers/technicians prints out desired ferrules by using a ferrule printing machine. Typical Ferrule The numbers/ letters on the ferrules will be given as per the approved electrical hook up or loop diagrams. This helps technicians to easily identify a particular loop/wiring from a series of terminal blocks and to troubleshoot the desired terminal connection. Separate numbers on the ferrules distinguish the positive and negative polarities of wires, thus ensure the polarity protection of the instrument. Cross Ferruling  As a wire is connected on its both ends, it is quite useful to use a cross reference method for wire identification. Unlike normal ferru...
Post a Comment
Read more