Interface Level Measurement using DP Transmitter

 Differential pressure (DP) transmitters are used to measure the interface of two fluids that have different specific gravities (S1 & S2). To make an interface measurement, the overall level must be at or above the low pressure tap at all times. It is important that the level be large enough to create a reasonable DP between the two specific gravity extremes. This measurement can be done with or without remote seals.

However, from a maintenance point of view, it may be easier to use a remote seal assembly; keeping the wet leg at a constant height can be difficult in some applications.

To determine the calibrated range for the transmitter, four assumptions need to be made:

At the lower calibrated value, 4 mA point, the tank is filled with the lighter fluid.

At the upper calibrated value, 20 mA point, the tank is filled with the heavier fluid.

The taps leading to the transmitter are flooded at all times. The overall level should be equal to or higher than the upper (low pressure) tap.

There is always a reference level seen by the low pressure side. This can be accomplished with either a remote seal system or a wet leg. The reference level must have a constant height and density. The calculation is modified slightly for wet leg systems when the density of the high and low pressure wet legs differ.

The measured level is composed of a combination of the two fluids:

L = L1S1 + L2S2

When the tank is filled with the lighter fluid, the transmitter will be at 4 mA (or 0% of span) and L2 = L:

HP = L2S2 + dSf

LP = dSf + hSf

At 4 mA, DP = HP – LP = L2S2 – hSf

When the tank is filled with the heavier fluid, the transmitter will be at 20 mA (or 100% of span) and L1 = L:

HP = L1S1 + dSf

LP = dSf + hSf

At 20 mA, DP = HP – LP = LS1 – hSf

Interface Level Measurement

This tool is used to calculate the DP transmitter ranges for interface measurement application

The formula used to calculate interface level using DP transmitter for interface measurement application are:

Where,

H = Distance between taps

L = Total Measured Level

S1 = Specific gravity of lighter fluid

S2 = Specific gravity of heavier fluid

Sf = Specific gravity of reference leg

Measured DP= After transmitter calibration, present DP value

Span = Difference between absolute of maximum and minimum range

LRV = Lower range value of transmitter in DP scale

I = Interface level

Interface Measurement using DP Transmitters

Advantages

• Low cost
• Simple to install
• No additional components required

Limitations

• Span must be sufficiently large enough to measure; either the distance between taps or the specific grabity difference m7ust be large
• Upper tap must be covered at all times.
• Small spans are susceptible to temperature induced errors.

Example Problem:

A vessel requires an interface measurement where the level is 150 inches. The vessel has two fluids with specific gravities of 1.0 and 1.08.

At 4mA, DP = L2S2 – hSf

DP = (150 x 1.0) – (150 x 0.934)

So at 4 mA = 9.9 inH2O DP

At 20mA, DP =  LS1 – hSf

DP = (150 x 1.08) – (150 x 0.934)

So at 20 mA = 21.9 inH2O DP

The calibrated span is 9.9 to 21.9 inH20. When the transmitter reads 9.9 inH20, the tank is filled with the lighter fluid. When the transmitter reads 21.9 inH20, the tank is filled with the heavier fluid.

To determine where the interface of a mixture of fluids is, use the DP reading as a percent of span. For example, if the transmitter output is 18.4 mA or a DP of 20.7 inH2O, the interface is calculated by using the formula: