Skip to main content

How to Calibrate Load Cells in Weighing Applications?

 Load cells are special force transducers used for measuring weight or force in various applications. These are integral to weighing systems in various industries, including aerospace, marine, automotive. The reason being they produce highly accurate load measurement data. That is why it is essential to inspect and calibrate them routinely.

Weighing scale calibration services ensure accurate load cell readings and help identify operational issues so that negative consequences can be prevented.

How to Calibrate Load Cells


Why You Should Calibrate Load Cells
Load cells show signs of wear and tear over a period of years. Frequency of use, environmental causes such as temperature, and aging are some of the contributing factors to the deterioration of load cells.

Faulty cables and instruments, particle accumulation and matter buildup, mechanical defects, incorrect installation, and the influence of electricity can also lead to inefficiency.

That is why routine calibrations should be performed to ensure the efficiency and accuracy of load cells. In the absence of frequent calibrations, load cells can give incorrect readings and produce erroneous data.

Routine calibration of load cells can help achieve accuracies of around 0.03 to 1%. As part of product liability, safety, and compliance in a Quality Management System, load cells are required to be calibrated to National standards.

Steps to Calibrate Load Cells in Weighing Applications
Before calibrating load cells, inspect whether the machine is giving correct measurement data.
We have mentioned three key indicators to evaluate whether the load cells and transducers are functioning correctly, these are:
  • When the system is unloaded or empty, the weight indication should return to zero.
  • The indicated weight must be double when the weight is doubled.
  • Irrespective of where the load is placed, the weight indicator should give equal readings.

Provided that all the conditions are met, it is safe to conclude that the load cells and transducers are working.

If you notice otherwise, follow the next steps.

Load cells can give inaccurate readings due to faulty cables and incorrect installation. Therefore, check the following before calibrating load cells:

Inspect the electrical cables and wires

Remember to place dummy cells in place of operational load cells until construction and welding work is finished.

After performing the preliminary tests, if you find that load cells are causing problems, conduct the following tests:

Physical Inspection:

This involves inspection for any physical damage in the load cell. Also, check for dents and cracks on all sides.

Note that if the load cell is not in its original shape and is altered- compressed, bent, or stretched, you need to replace the cell.


Bridge Resistance:

This test should be done when there is no load and the system is disconnected from the weight controller. Now measure the excitation leads for input resistance, and signal leads for output resistance.

Compare the readings with the load cell specifications. out-of-tolerance readings are often caused by power fluctuation.

Zero Balance:

Residual stress in the sensing area can often cause a shift in zero balance. If a load cell is overloaded repeatedly over multiple operational cycles, residual stress builds up.

Check the output of a load cell with a voltmeter when the system is empty. It must be within 0.1% of the mentioned zero output signal. If it exceeds the zero balance tolerance band, the cell might be damaged.

Resistance to Ground:

Connect the input, output, and ground leads. With the help of an ohmmeter, check the resistance between the load cell body and the leads. If the reading does not reach 5,000 megaohms, separate the ground wire, and repeat the test. If it fails again, the cell could be damaged.

By following these steps, you would not only ensure load cells are functioning correctly but would also be able to prevent and take precautions against any potential damages.

Labels:

Comments

Post a Comment

Popular posts from this blog

PLC Program for Mixing Tank

 Create a ladder diagram for controlling a batch mixing process. Implement a PLC program for mixing tank or Mixing Process using PLC Ladder Logic. PLC Program for Mixing Tank Fig : Mixing tank A tank is used to mix two liquids. The required control circuit operates as follows: A. When the START button is pressed, solenoids A and B energize. This permits the two liquids to begin filling the tank. B. When the tank is filled, the float switch trips. This de-energizes solenoids A and B and starts the motor used to mix the liquids together. C. The motor is permitted to run for 1 minute. After 1 minute has elapsed, the motor turns off and solenoid C energizes to drain the tank. D. When the tank is empty, the float switch de- energizes solenoid C. E. A STOP button can be used to stop the process at any point. F. If the motor becomes overloaded, the action of the entire circuit will stop. G. Once the circuit has been energized, it will continue to operate until it is manually stopped. Solution...
1 comment
Read more

What is Relay? How it Works? Types, Applications, Testing

 We use relays for a wide range of applications such as home automation, cars and bikes (automobiles), industrial applications, DIY Projects, test and measurement equipment, and many more. But what is Relay? How a Relay Works? What are the Applications of Relays? Let us explore more about relays in this guide. What is a Relay? A Relay is a simple electromechanical switch. While we use normal switches to close or open a circuit manually, a Relay is also a switch that connects or disconnects two circuits. But instead of a manual operation, a relay uses an electrical signal to control an electromagnet, which in turn connects or disconnects another circuit. Relays can be of different types like electromechanical, solid state. Electromechanical relays are frequently used. Let us see the internal parts of this relay before knowing about it working. Although many different types of relay were present, their working is same. Every electromechanical relay consists of an consists of an Elect...
1 comment
Read more

Chlorine dioxide Analyzer Principle

 Chlorine dioxide measurement Chlorine dioxide (ClO2) is an instable, non-storable, toxic gas with a characteristic scent. The molecule consists of one chlorine atom and two oxygen atoms – represented in the chemical formula ClO2. It is very reactive. To avoid the risk of spontaneous explosions of gaseous chlorine dioxide or concentrated solutions, it is generally handled in dilution with low concentrations. ClO2 is soluble in water, but tends to evaporate quickly. Typically it is prepared on site, for example from hydrochloric acid and sodium chlorite. The procedure provides solutions with approx. 2 g/l ClO2 that can be safely handled and stored for several days. Image Credits : krohne Sensor Parts : Reference electrode Applied chlorine dioxide specific potential Current needed to maintain the constant potential Counter electrode Measuring electrode The disinfection effect of ClO2 is due to the transfer of oxygen instead of chlorine, so that no chlorinated byproducts are formed. C...
6 comments
Read more