Ultrasonic Doppler Flow Meter Advantages and Disadvantages

A Ultrasonic Doppler flow meter transmits an acoustic signal into the flow stream at a specific frequency. This signal reflects off particulate, either solids or gas bubbles.

Ultrasonic Doppler Flow Meter

The reflected signal is detected by the receive transducer. The flow meter compares the transmit & receive frequencies & computes the frequency shift. This frequency shift is proportional to the liquid’s flow velocity & is known as the Doppler’s effect.

Doppler Flow Meters are only used for liquids containing gas bubbles or particulates. Some of the applications where Doppler has advantage over Transmit time are Treated Waste Water, Raw Water, Slurries, Sewage, Viscous Liquids, Acid, Pulp Stock, Food Products, Aerated Water, Cooling Water etc.

Advantages of Doppler Flow Meter

The main advantage of doppler flow meter is its non-intrusive design.

An acoustic-coupling compound is used on the surface of the pipe and the sensors are simply held in place to take a measurement or, for a more permanent installation, they are strapped around the pipe.

Some manufacturers offer a special clamp-on probe which allows connection to smaller pipe sizes.

Other advantages include :

Easy installation and removal.

No process downtime during installation.

No moving parts to wear out.

No process contamination.

Works well with dirty or corrosive fluids.

No leakage potential.

Insensitive to liquid temperature, viscosity, density or pressure variations.

Disadvantages of Doppler Flow Meter

The main disadvantage of the doppler flow meter is the fact that the liquid stream must have particulates, bubbles, or other types of solids in order to reflect the ultrasonic signal. This means that the doppler flow meter is not a good choice for the water and very clean fluids.

The another disadvantage is that the accuracy can depend on particle-size distribution and concentration and also on any relative velocity that may exist between the particulates and the fluid. if there are not enough particulates available, the repeatability will degrade.

The other potential problem of this technology is that it can have trouble operating at very low flow velocities.

Applications of Doppler Flow Meter

Being an non-intrusive, Doppler flow meters have a wide variety of applications.

Some of them include:

1.Influent and effluent water flow.

2.Digester feed control.

3.Waste water.

4.Crude oil flow.

5.Mining slurries.

6.Acids.

7.Liquified gases.

Comments

PLC Program for Mixing Tank

Create a ladder diagram for controlling a batch mixing process. Implement a PLC program for mixing tank or Mixing Process using PLC Ladder Logic. PLC Program for Mixing Tank Fig : Mixing tank A tank is used to mix two liquids. The required control circuit operates as follows: A. When the START button is pressed, solenoids A and B energize. This permits the two liquids to begin ﬁlling the tank. B. When the tank is ﬁlled, the ﬂoat switch trips. This de-energizes solenoids A and B and starts the motor used to mix the liquids together. C. The motor is permitted to run for 1 minute. After 1 minute has elapsed, the motor turns off and solenoid C energizes to drain the tank. D. When the tank is empty, the ﬂoat switch de- energizes solenoid C. E. A STOP button can be used to stop the process at any point. F. If the motor becomes overloaded, the action of the entire circuit will stop. G. Once the circuit has been energized, it will continue to operate until it is manually stopped. Solution...

What is Relay? How it Works? Types, Applications, Testing

We use relays for a wide range of applications such as home automation, cars and bikes (automobiles), industrial applications, DIY Projects, test and measurement equipment, and many more. But what is Relay? How a Relay Works? What are the Applications of Relays? Let us explore more about relays in this guide. What is a Relay? A Relay is a simple electromechanical switch. While we use normal switches to close or open a circuit manually, a Relay is also a switch that connects or disconnects two circuits. But instead of a manual operation, a relay uses an electrical signal to control an electromagnet, which in turn connects or disconnects another circuit. Relays can be of different types like electromechanical, solid state. Electromechanical relays are frequently used. Let us see the internal parts of this relay before knowing about it working. Although many different types of relay were present, their working is same. Every electromechanical relay consists of an consists of an Elect...

Chlorine dioxide Analyzer Principle

Chlorine dioxide measurement Chlorine dioxide (ClO2) is an instable, non-storable, toxic gas with a characteristic scent. The molecule consists of one chlorine atom and two oxygen atoms – represented in the chemical formula ClO2. It is very reactive. To avoid the risk of spontaneous explosions of gaseous chlorine dioxide or concentrated solutions, it is generally handled in dilution with low concentrations. ClO2 is soluble in water, but tends to evaporate quickly. Typically it is prepared on site, for example from hydrochloric acid and sodium chlorite. The procedure provides solutions with approx. 2 g/l ClO2 that can be safely handled and stored for several days. Image Credits : krohne Sensor Parts : Reference electrode Applied chlorine dioxide specific potential Current needed to maintain the constant potential Counter electrode Measuring electrode The disinfection effect of ClO2 is due to the transfer of oxygen instead of chlorine, so that no chlorinated byproducts are formed. C...

TILI Automation

Search This Blog