Skip to main content

Square-Root in DCS or Flow Transmitter?

 This is mostly known to everyone that a square root Function is required for Orifice Flow Transmitter as the relationship of flow versus pressure is not linear but has a square-root relationship.

But the next question is? where should you do this square-root function?

In Transmitter or DCS or both or none?

Note: we can do this square root function in two ways. one using the physical device called square-root extractor and this is an old method. Second is using the software configuration either in transmitter or in DCS. Here we are discussing the second method.

Interface issue between System and field instrument engineer.

The first point of caution is the proper interface between the requisition (field) engineers and system engineers.

Sometimes the engineer purchasing transmitter assumes it will be done in DCS.

While the system engineer assumes it will be done in Transmitter.

And NOBODY does it.

Similarly, the converse is also true.

The Square-root extraction is done at both places, which again is incorrect.

In short, NOBODY doing it

Or EVERYBODY (Field as well DCS) doing it

Should be avoided.

It should be done in one place ONLY.

Next Question where should you prefer doing the extraction?

Well after having a discussion with a few dependable Vendors they suggest it should be done at the system side.

Reason:-  Some Transmitter’s electronic computational capability is not superior as compared to System (DCS/SIS) side.

 So it is advisable to give that task to the System side.

Please note this is just a recommendation as I have done projects where the client preferred having it done in Transmitter while I have also worked on projects where it was done on the System side.

 But if it is not enforced by client you could do it at the system side.

Display a Square-rooted output at field But Square-root extraction require in DCS?

The situation:- Suppose you want square-root extraction to be done in the System side, But the Transmitter in the field has display, so in the field when someone looks at the transmitter then he would not have a calculator to read the transmitter’s output and do the extraction manually.

So “We would need the transmitter to display the square-rooted output in the field as that is what is useful for someone looking at the display in field”

But we want the extraction to be done at the system end.

The solution:- This feature is available with various vendors but it should be properly communicated.

 The following information must be passed on:-

 1. Transmitter (Tx) will be blind or have a display

2. What range Tx should display example:- 0 to 100 lb/hr

3. Clearly indicate: The Extraction is to be done in the Control system side.

 In order to display the “Square rooted output” the transmitter will do it locally just for display but won’t send the Square-root extracted signal to DCS. That task will be done by DCS.

 Thanks for reading !!

 I hope it’s been of value to you.

PS: This is as per the best of my current understanding.



Labels:

Comments

Post a Comment

Popular posts from this blog

PLC Program for Mixing Tank

 Create a ladder diagram for controlling a batch mixing process. Implement a PLC program for mixing tank or Mixing Process using PLC Ladder Logic. PLC Program for Mixing Tank Fig : Mixing tank A tank is used to mix two liquids. The required control circuit operates as follows: A. When the START button is pressed, solenoids A and B energize. This permits the two liquids to begin filling the tank. B. When the tank is filled, the float switch trips. This de-energizes solenoids A and B and starts the motor used to mix the liquids together. C. The motor is permitted to run for 1 minute. After 1 minute has elapsed, the motor turns off and solenoid C energizes to drain the tank. D. When the tank is empty, the float switch de- energizes solenoid C. E. A STOP button can be used to stop the process at any point. F. If the motor becomes overloaded, the action of the entire circuit will stop. G. Once the circuit has been energized, it will continue to operate until it is manually stopped. Solution...
1 comment
Read more

What is Relay? How it Works? Types, Applications, Testing

 We use relays for a wide range of applications such as home automation, cars and bikes (automobiles), industrial applications, DIY Projects, test and measurement equipment, and many more. But what is Relay? How a Relay Works? What are the Applications of Relays? Let us explore more about relays in this guide. What is a Relay? A Relay is a simple electromechanical switch. While we use normal switches to close or open a circuit manually, a Relay is also a switch that connects or disconnects two circuits. But instead of a manual operation, a relay uses an electrical signal to control an electromagnet, which in turn connects or disconnects another circuit. Relays can be of different types like electromechanical, solid state. Electromechanical relays are frequently used. Let us see the internal parts of this relay before knowing about it working. Although many different types of relay were present, their working is same. Every electromechanical relay consists of an consists of an Elect...
1 comment
Read more

Chlorine dioxide Analyzer Principle

 Chlorine dioxide measurement Chlorine dioxide (ClO2) is an instable, non-storable, toxic gas with a characteristic scent. The molecule consists of one chlorine atom and two oxygen atoms – represented in the chemical formula ClO2. It is very reactive. To avoid the risk of spontaneous explosions of gaseous chlorine dioxide or concentrated solutions, it is generally handled in dilution with low concentrations. ClO2 is soluble in water, but tends to evaporate quickly. Typically it is prepared on site, for example from hydrochloric acid and sodium chlorite. The procedure provides solutions with approx. 2 g/l ClO2 that can be safely handled and stored for several days. Image Credits : krohne Sensor Parts : Reference electrode Applied chlorine dioxide specific potential Current needed to maintain the constant potential Counter electrode Measuring electrode The disinfection effect of ClO2 is due to the transfer of oxygen instead of chlorine, so that no chlorinated byproducts are formed. C...
6 comments
Read more